stand cover

Styrgrossisten AB

Stand: J:02
Products and systems for industrial and electrical installations
Lighting
Lighting automation
https://www.styrgrossisten.se

About us

Styrgrossisten is a modern active Whole Saler focusing on building automation with products withing standards as KNX & Dali.

Products & services

product-image

eelectron KNX - Switching Actuator / Binary Input module with 16 out / 16 inputs and backup by SD-card

eelectron KNX combined 16-channel Switch actuator and 16-channel Binary input. The product has 16 potential-free 16A relay channels and 16 potential-free binary inputs for connecting e.g. Push buttons, Alarm signals, Time channels from other systems, Hard signals from other systems, etc. The relay outputs can be interlocked and used to control Blinds and also Thermal actuators for climate control, lighting, etc. When the product is configured to control Thermal actuators, the channels can be controlled with 1-byte value (0-100%). If all channels are switched to Shutter function, the product becomes an 8-channel Shutter actuator. If all channels are switched to Fancoil function, the product can handle 4 2-pipe fan coil controls, i.e. 4 Zones Fancoil with 3 fan stages and 1 actuator for Cooling (or) Heating. The functionality of the outputs can also be mixed to combine control of both Blinds and individually controlled relay channels for Tex. lighting. In ETS, functions such as Tex. Automatic staircase and other time functions are activated for each relay channel. See the manual or open the product in ETS for more info. The inputs can be set in several different modes: T/F, Dimmer, Shutter control, etc. SD card reader on the front of the product for automatic backup and recovery of broken product. The product saves the application program and individual address on the SD card when downloading the application from ETS. Memory card included. If the product needs to be replaced, the replacement product can be easily restored via the SD card. Hand buttons are on the front of the product for manual/physical operation of the respective output.

product-image

eelectron KNX - Push button interface with Temperature input and built in Thermostat

eelectron AD84C01KNX module includes 4 digital inputs to interface dry potential contacts and 4 analog or digital inputs for dry contacts or temperature sensors and 4 led outputs. Digital inputs can interface sensors, traditional buttons, etc; 4 low voltage/current outputs can drive LED for synoptics panels or switches. Inputs 5 ÷ 8, set as analog inputs, can enable up to 2 temperature probes (with On/Off threshold) and 4 thermostats to control heating and cooling equipments, valves, 2 and 4 pipes fan coils; etc.. The device is equipped with appropriate communication interface with the bus type TP1 (twisted pair) KNX European standard, according CEI EN 50090.

product-image

Iddero - Verso 4,3” KNX Touchscreen with IP-connection and App for iOS and Android

The new VERSO+IP retains the elegant design, attractive visualisation, and advanced functionality of the Iddero Verso KNX room controller, and adds an Ethernet port for IP connectivity. Remote control from smartphones and tablets. Get anytime, anywhere remote access to your VERSO+IP from your smartphone or tablet. Mobile apps available for iOS and Android. No worries; no hassles. Both direct (LAN) connection and cloud-based operation are supported; no additional configuration required. Communications are fully encrypted and 100% secure. With the new VERSO+IP, you just can't go wrong.

product-image

DINUY KNX - RF Dimming actuator 1-ch DALI Broadcast 64ECG

1-channel KNX RF S-Mode wireless Dimming actuator for DALI Drivers or Ballasts, with LED or Fluorescence lighting. Allows upgrading the KNX installation without placing KNX bus wires. Operates in KNX RF+ protocol in System-Mode. Communication with the KNX Bus must be carried out using a KNX / KNX RF S-Mode media coupler: “CO K5X 002”. Power supply: 230VAC 50/60Hz. Different functions which can be configured with ETS: Time of soft on and off, Maximum and minimum dimming level, Behavior after on telegram, Staircase time switch and Sequential operation modes, Auxiliary Pushbutton input with configurable operation. It incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers. Adjustable behavior in case of bus voltage failure. 5 pre-configured scenes. Flush mounted in junction box. Programming and commissioning by ETS5 via the KNX-RF+ USB stick “CO K5X 001”.

product-image

eelectron KNX Närvarodetektor 12m Multisensor Vit

Eelectron KNX presence detector. Circular area for detection within 12m diameter at a mounting height of 3m. Supplied with mounting details for flush mounting in, for example, suspended ceiling tiles and for flush mounting box. Access to programming button from the front for easy commissioning. On the back/top of the product there is a connection for KNX bus and 3 digital potential-free contacts. Example of use: 3 push buttons or magnetic contacts for windows, doors and folding walls. Built-in sensors: presence sensor, light sensor, temperature sensor, acoustic sensor, sound sensor, humidity sensor. Sensor technology: 1 Passive IR Detection area (diameter) at different mounting heights: Mounting height 2.5m = 10m Mounting height 3.0m = 12m Mounting height 3.5m = 13m Mounting height 4.0m = 14m AREA OF USE Residence, shop, hospital, nursing home, hotel, office, conference room, warehouse, classroom, garage, etc. PROJECT SAVINGS Can be delivered pre-programmed and addressed with mounted label for individual address for faster commissioning process. Possibility of major financial savings for projects. Contact us for more information. COLOR AND SHAPE The product is available in black and white. For project-specific requests, the product can be delivered in any color. Contact us for more information. FUNCTIONS AND PROGRAMMING 5 individually adjustable control channels/blocks, constant light regulator (independent of the 5 control channels), 2-stage dimming function, blocking function, brightness threshold, 12 freely configurable logic objects, virtual holder (virtual card reader for hotel rooms). Thermostat function for climate control with or without fan coil: Individual control for heating/cooling or combined automatic climate control with interlock and deadband. Control function for Tunable White “Circadian Daylight Rhythm”. Adjustable sensitivity for the presence sensor. Built-in temperature sensor. Hygrostat function with threshold setting, etc.